bond_style table command¶
Accelerator Variants: table/omp
bond_style table style N
style = linear or spline = method of interpolation
N = use N values in table
bond_style table linear 1000 bond_coeff 1 file.table ENTRY1
Style table creates interpolation tables of length N from bond potential and force values listed in a file(s) as a function of bond length. The files are read by the bond_coeff command.
The interpolation tables are created by fitting cubic splines to the file values and interpolating energy and force values at each of N distances. During a simulation, these tables are used to interpolate energy and force values as needed. The interpolation is done in one of 2 styles: linear or spline.
For the linear style, the bond length is used to find 2 surrounding table values from which an energy or force is computed by linear interpolation.
For the spline style, a cubic spline coefficients are computed and stored at each of the N values in the table. The bond length is used to find the appropriate set of coefficients which are used to evaluate a cubic polynomial which computes the energy or force.
The following coefficients must be defined for each bond type via the bond_coeff command as in the example above.
The filename specifies a file containing tabulated energy and force values. The keyword specifies a section of the file. The format of this file is described below.
The format of a tabulated file is as follows (without the parenthesized comments):
# Bond potential for harmonic (one or more comment or blank lines) HAM (keyword is the first text on line) N 101 FP 0 0 EQ 0.5 (N, FP, EQ parameters) (blank line) 1 0.00 338.0000 1352.0000 (index, bond-length, energy, force) 2 0.01 324.6152 1324.9600 ... 101 1.00 338.0000 -1352.0000
A section begins with a non-blank line whose first character is not a “#”; blank lines or lines starting with “#” can be used as comments between sections. The first line begins with a keyword which identifies the section. The line can contain additional text, but the initial text must match the argument specified in the bond_coeff command. The next line lists (in any order) one or more parameters for the table. Each parameter is a keyword followed by one or more numeric values.
The parameter “N” is required and its value is the number of table entries that follow. Note that this may be different than the N specified in the bond_style table command. Let Ntable = N in the bond_style command, and Nfile = “N” in the tabulated file. What LAMMPS does is a preliminary interpolation by creating splines using the Nfile tabulated values as nodal points. It uses these to interpolate as needed to generate energy and force values at Ntable different points. The resulting tables of length Ntable are then used as described above, when computing energy and force for individual bond lengths. This means that if you want the interpolation tables of length Ntable to match exactly what is in the tabulated file (with effectively no preliminary interpolation), you should set Ntable = Nfile.
The “FP” parameter is optional. If used, it is followed by two values fplo and fphi, which are the derivatives of the force at the innermost and outermost bond lengths. These values are needed by the spline construction routines. If not specified by the “FP” parameter, they are estimated (less accurately) by the first two and last two force values in the table.
The “EQ” parameter is also optional. If used, it is followed by a the equilibrium bond length, which is used, for example, by the fix shake command. If not used, the equilibrium bond length is to the distance in the table with the lowest potential energy.
Following a blank line, the next N lines list the tabulated values. On each line, the first value is the index from 1 to N, the second value is the bond length r (in distance units), the third value is the energy (in energy units), and the fourth is the force (in force units). The bond lengths must range from a LO value to a HI value, and increase from one line to the next. If the actual bond length is ever smaller than the LO value or larger than the HI value, then the calculation is aborted with an error, so it is advisable to cover the whole range of possible bond lengths.
Note that one file can contain many sections, each with a tabulated potential. LAMMPS reads the file section by section until it finds one that matches the specified keyword.
Styles with a gpu, intel, kk, omp, or opt suffix are functionally the same as the corresponding style without the suffix. They have been optimized to run faster, depending on your available hardware, as discussed on the Accelerator packages page. The accelerated styles take the same arguments and should produce the same results, except for round-off and precision issues.
These accelerated styles are part of the GPU, INTEL, KOKKOS, OPENMP and OPT packages, respectively. They are only enabled if LAMMPS was built with those packages. See the Build package page for more info.
You can specify the accelerated styles explicitly in your input script by including their suffix, or you can use the -suffix command-line switch when you invoke LAMMPS, or you can use the suffix command in your input script.
See the Accelerator packages page for more instructions on how to use the accelerated styles effectively.
Restart, fix_modify, output, run start/stop, minimize info¶
This bond style writes the settings for the “bond_style table” command to binary restart files, so a bond_style command does not need to specified in an input script that reads a restart file. However, the coefficient information is not stored in the restart file, since it is tabulated in the potential files. Thus, bond_coeff commands do need to be specified in the restart input script.
This bond style can only be used if LAMMPS was built with the MOLECULE package. See the Build package page for more info.